1
JEE Advanced 2023 Paper 1 Online
MCQ (Single Correct Answer)
+3
-1
A bar of mass $M=1.00 \mathrm{~kg}$ and length $L=0.20 \mathrm{~m}$ is lying on a horizontal frictionless surface. One end of the bar is pivoted at a point about which it is free to rotate. A small mass $m=0.10 \mathrm{~kg}$ is moving on the same horizontal surface with $5.00 \mathrm{~m} \mathrm{~s}^{-1}$ speed on a path perpendicular to the bar. It hits the bar at a distance $L / 2$ from the pivoted end and returns back on the same path with speed v. After this elastic collision, the bar rotates with an angular velocity $\omega$.

Which of the following statement is correct?
A
$\omega=6.98 ~\mathrm{rad}~ \mathrm{s}^{-1}$ and $\mathrm{v}=4.30 \mathrm{~m} \mathrm{~s}^{-1}$
B
$\omega=3.75 ~\mathrm{rad} ~\mathrm{s}^{-1}$ and $\mathrm{v}=4.30 \mathrm{~m} \mathrm{~s}^{-1}$
C
$\omega=3.75 ~\mathrm{rad}~ \mathrm{s}^{-1}$ and $\mathrm{v}=10.0 \mathrm{~m} \mathrm{~s}^{-1}$
D
$\omega=6.80 ~\mathrm{rad} ~\mathrm{s}^{-1}$ and $\mathrm{v}=4.10 \mathrm{~m} \mathrm{~s}^{-1}$
2
JEE Advanced 2022 Paper 2 Online
MCQ (Single Correct Answer)
+3
-1

A flat surface of a thin uniform disk $A$ of radius $R$ is glued to a horizontal table. Another thin uniform disk $B$ of mass $M$ and with the same radius $R$ rolls without slipping on the circumference of $A$, as shown in the figure. A flat surface of $B$ also lies on the plane of the table. The center of mass of $B$ has fixed angular speed $\omega$ about the vertical axis passing through the center of $A$. The angular momentum of $B$ is $n M \omega R^{2}$ with respect to the center of $A$. Which of the following is the value of $n$ ?

A
2
B
5
C
$\frac{7}{2}$
D
$\frac{9}{2}$
3
JEE Advanced 2022 Paper 1 Online
MCQ (Single Correct Answer)
+3
-1

List I describes four systems, each with two particles $A$ and $B$ in relative motion as shown in figures. List II gives possible magnitudes of their relative velocities (in $m s^{-1}$ ) at time $t=\frac{\pi}{3} s$.

List-I List-II
(I) $A$ and $B$ are moving on a horizontal circle of radius $1 \mathrm{~m}$ with uniform angular speed $\omega=1 \mathrm{rad} \mathrm{s}^{-1}$. The initial angular positions of $A$ and $B$ at time $t=0$ are $\theta=0$ and $\theta=\frac{\pi}{2}$, respectively.
(P) $\frac{\sqrt{3}+1}{2}$
(II) Projectiles $A$ and $B$ are fired (in the same vertical plane) at $t=0$ and $t=0.1 \mathrm{~s}$ respectively, with the same speed $v=\frac{5 \pi}{\sqrt{2}} \mathrm{~m} \mathrm{~s}^{-1}$ and at $45^{\circ}$ from the horizontal plane. The initial separation between $A$ and $B$ is large enough so that they do not collide. $\left(g=10 \mathrm{~ms}^{-2}\right)$.
(Q) $\frac{\sqrt{3}-1}{\sqrt{2}}$
(III) Two harmonic oscillators $A$ and $B$ moving in the $x$ direction according to $x_{A}=x_{0} \sin \frac{t}{t_{0}}$ and $x_{B}=x_{0} \sin \left(\frac{t}{t_{0}}+\frac{\pi}{2}\right)$ respectively, starting from $t=0$. Take $x_{0}=1 \mathrm{~m}, t_{0}=1 \mathrm{~s}$.
(R) $\sqrt{10}$
(IV) Particle $A$ is rotating in a horizontal circular path of radius $1 \mathrm{~m}$ on the $x y$ plane, with constant angular speed $\omega=1 \mathrm{rad} \mathrm{s}^{-1}$. Particle $B$ is moving up at a constant speed $3 \mathrm{~m} \mathrm{~s}^{-1}$ in the vertical direction as shown in the figure. (Ignore gravity.)
(S) $\sqrt{2}$
(T) $\sqrt{25\pi^{2}+1}$

Which one of the following options is correct?

A
I $\rightarrow$ R, II $\rightarrow$ T, III $\rightarrow$ P, IV $\rightarrow$ S
B
I $\rightarrow$ S, II $\rightarrow$ P, III $\rightarrow$ Q, IV $\rightarrow$ R
C
I $\rightarrow$ S, II $\rightarrow$ T, III $\rightarrow$ P, IV $\rightarrow$ R
D
I $\rightarrow$ T, II $\rightarrow$ P, III $\rightarrow$ R, IV $\rightarrow$ S
4
JEE Advanced 2020 Paper 1 Offline
MCQ (Single Correct Answer)
+3
-1
A small roller of diameter 20 cm has an axle of diameter 10 cm (see figure below on the left). It is on a horizontal floor and a meter scale is positioned horizontally on its axle with one edge of the scale on top of the axle (see figure on the right). The scale is now pushed slowly on the axle so that it moves without slipping on the axle, and the roller starts rolling without slipping. After the roller has moved 50 cm, the position of the scale will look like (figures are schematic and not drawn to scale)
A
B
C
D
EXAM MAP
Medical
NEET
Graduate Aptitude Test in Engineering
GATE CSEGATE ECEGATE EEGATE MEGATE CEGATE PIGATE IN
Civil Services
UPSC Civil Service
Defence
NDA
CBSE
Class 12