ExamSIDE (Powered by ExamGOAL)
Questions
PREVIOUS NEXT
1
GATE EE 2002
MCQ (Single Correct Answer)
+1
-0.3
Consider a long, two-wire line composed of solid round conductors. The radius of both conductors is $$0.25$$ cm and the distance between their centers is $$1$$m. If this distance is doubled, then the inductance per unit length.
A
Doubles
B
Halves
C
Increases but does not double
D
Decreases but does not halve
2
GATE EE 2002
MCQ (Single Correct Answer)
+1
-0.3
A long wire composed of a smooth round conductor runs above and parallel to the ground (assumed to be a large conducting plane). A high voltage exists between the conductor and the ground. The maximum electric stress occurs at
A
The upper surface of the conductor
B
The lower surface of the conductor
C
The ground surface
D
Midway between the conductor and ground
3
GATE EE 2001
MCQ (Single Correct Answer)
+1
-0.3
A lossless radial transmission line with surge impedance loading
A
Takes negative VAR at sending end and zero VAR at receiving end.
B
Takes positive VAR at sending end and zero VAR at receiving end.
C
Has flat voltage profile and unity power factor at all points along it.
D
Has sending end voltage higher than receiving end voltage and unity power factor at sending end.
4
GATE EE 1999
MCQ (Single Correct Answer)
+1
-0.3
The load carrying capability of a long AC transmission line is
A
Always limited by the conductor size
B
Limited by stability considerations.
C
Reduced at a low ambient temperatures.
D
Decreased by the use of bundled conductors of single conductors.
PREVIOUS NEXT
GATE EE Subjects
Electric Circuits
Network Elements Network Theorems Three Phase Circuits Transient Response Sinusoidal Steady State Analysis Graph Theory Two Port Networks
Electromagnetic Fields
Time Varying Fields Electrostatics Magnetostatics
Signals and Systems
Linear Time Invariant Systems Continuous and Discrete Time Signals Continuous Time Signal Fourier Transform Continuous Time Periodic Signal Fourier Series Discrete Time Signal Z Transformation Miscellaneous Continuous Time Signal Laplace Transform Sampling Theorem
Electrical Machines
Induction Machines D.C Machines Synchronous Machines Transformers
Engineering Mathematics
Linear Algebra Differential Equations Calculus Probability and Statistics Numerical Methods Vector Calculus Transform Theory Complex Variable
General Aptitude
Verbal Ability Logical Reasoning Numerical Ability
Power System Analysis
Parameters and Performance of Transmission Lines Power Generation Cost Power System Stability Symmetrical Components and Symmetrical and Unsymmetrical Faults Circuit Breaker Switch Gear and Protection Per Unit System Load Flow Studies High Voltage Dc Transmission Generating Power Station
Electrical and Electronics Measurement
Error Analysis and Measurement Basic of Indicating Instruments Potentiometer and Instrument Transformers Measurement of Resistance and A.C Bridges Measurement of Energy and Power Digital Voltmeters Questions Cathode Ray Oscilloscope
Analog Electronics
Diode Circuits and Applications Bjt and Mosfet Biasing Small Signal Modeling Feedback Amplifiers and Oscillator Circuits Operational Amplifier Frequency Response 555 Timer
Control Systems
Block Diagram and Signal Flow Graph Polar Nyquist and Bode Plot State Variable Analysis Basics of Control System Routh Hurwitz Stability Time Response Analysis Root Locus Techniques Controller and Compensator
Power Electronics
Choppers and Commutation Techniques Ac Voltage Controllers Single and Three Phase Rectifier Power Semiconductor Devices Inverters
Digital Electronics
Boolean Algebra Logic Gates Combinational Circuits Minimization Logic Families and Memories Sequential Circuits Analog to Digital and Digital to Analog Converter Microprocessor
EXAM MAP
Joint Entrance Examination
JEE MainJEE AdvancedWB JEEBITSATMHT CETKCETCOMEDKVITEEEAP EAPCET
Medical
NEETAIIMS
Graduate Aptitude Test in Engineering
GATE CSEGATE ECEGATE EEGATE MEGATE CEGATE PIGATE IN
Civil Services
UPSC Civil Service
Defence
NDA
Staff Selection Commission
SSC CGL Tier I
CBSE
Class 12