ExamSIDE (Powered by ExamGOAL)
Questions
PREVIOUS
1
GATE CE 2024 Set 1
MCQ (Single Correct Answer)
+2
-0.833

For assessing the compliance with the emissions standards of incineration plants, a correction needs to be applied to the measured concentrations of air pollutants. The emission standard (based on 11% Oxygen) for HCl is 50 mg/Nm3 and the measured concentrations of HCl and Oxygen in flue gas are 42 mg/Nm3 and 13%, respectively.

Assuming 21% Oxygen in air, the CORRECT statement is:

A

No compliance, as the corrected HCl emission is greater than the emission standard.

B

Compliance is there, as the corrected HCl emission is less than the emission standard.

C

Compliance is there, as there is no need to apply the correction since Oxygen is greater than 11% and HCl emission is lesser than the emission standard.

D

No compliance, as the Oxygen is greater than 11% in the flue gas.

2
GATE CE 2014 Set 1
Fill in the Blanks
+2
-0
A straight 100 m long raw water gravity main is to carry water from an intake structure to the jack well of a water treatment plant. The required flow through this water main is 0.21 $$m^3/s$$. Allowable velocity through the main is 0.75 m/s. Assume f = 0.01, g = 9.81 $$m/s^2$$. The minimum gradient (in cm/100m length) to be given to this gravity main so that the required amount of water flows without any difficulty is _____.
PREVIOUS
GATE CE Subjects
Construction Material and Management
Critical Path Method Construction Materials Program Evolution Review Technique
Geomatics Engineering Or Surveying
Levelling Traversing Theodolites and Plane Table Surveying Measurement of Area, Volume and Theory of Errors and Survey Adjustment Field Astronomy and Photogrammetric Surveying Basics of GIS, GPS and Remote Sensing Angular Measurements and Compass Survey Basic Concepts Linear Measurements and Chain Survey
Engineering Mechanics
Equilibrium of Force Systems Work Energy Principle and Impulse Momentum Equation
Hydrology
Precipitation and Frequency of Rainfall Data Evaporation and Transpiration Infiltration Hydrograph Flood Estimation and Flood Routing
Transportation Engineering
Highway Devolopment and Planning Highway Geometric Design Traffic Engineering Highway Materials Pavement Design Railway, Runway and Taxiway Design
Strength of Materials Or Solid Mechanics
Centroid and Moment of Inertia Torsion Pure Bending Shear Stress In Beams Strain Energy Method Columns and Struts Complex Stress Deflection of Beams Thin Cylinder Simple Stresses Shear Force and Bending Moment Propped Cantilever Beam
Reinforced Cement Concrete
Singly Reinforced Sections Workmenship and Fundamentals Doubly Reinforced Sections Flanged Beams Limit State of Collapse Shear Limit State of Collapse Torsion Limit State of Collapse Compression Footings Bond Limit State of Serviceability Prestressed Concrete Slabs
Steel Structures
Eccentric Connections Plate Girder Tension Members Welded Connections Materials and Specifications Riveted Joints and Bolted Joints Beams Compression Members
Irrigation
Gravity Dams and Spillways Water Requirement of Crops
Environmental Engineering
Sources and Coveyances Water Quality Control of Water Treatment of Water Water Demand Waste Water Characteristics Treatment of Sewage Disposal of Sewage Effluent Solid Waste Management Air Pollution Noise Pollution
Engineering Mathematics
Probability and Statistics Differential Equations Transform Theory Calculus Complex Variable Linear Algebra Vector Calculus Numerical Methods
Structural Analysis
Stability and Static Indeterminacy Methods of Analysis Plastic Analysis Moment Distribution Method Indeterminacy Energy Principle Influence Line Diagram Arches and Cable Slope Deflection Method Truss Matrix Method
Geotechnical Engineering
Origin of Soils Definitions and Properties of Soils Classification of Soils and Clay Mineralogy Effective Stress and Permeability Seepage Analysis Compaction of Soil Compressibility and Consolidation Shear Strength of Soil Stress Distribution of Soil Retaining Wall and Earth Pressure Stability of Slopes Shallow Foundation Pile Foundation Soil Stabilization
Fluid Mechanics and Hydraulic Machines
Fluid Pressure and Measurement Fluid Dynamics Boundary Layer Theory Drag and Lift Flow Through Pipes Open Channel Flow Hydraulic Machines Properties of Fluids Fluid Statics
General Aptitude
Numerical Ability Logical Reasoning Verbal Ability
EXAM MAP
Joint Entrance Examination
JEE MainJEE AdvancedWB JEEBITSATMHT CETKCETCOMEDKVITEEEAP EAPCET
Medical
NEETAIIMS
Graduate Aptitude Test in Engineering
GATE CSEGATE ECEGATE EEGATE MEGATE CEGATE PIGATE IN
Civil Services
UPSC Civil Service
Defence
NDA
Staff Selection Commission
SSC CGL Tier I
CBSE
Class 12