ExamSIDE (Powered by ExamGOAL)
Questions
PREVIOUS NEXT
1
GATE CE 2005
MCQ (Single Correct Answer)
+2
-0.6
A truss is shown in the figure. Members are to equal cross section $$A$$ and same modulus of elasticity $$E.$$ $$A$$ vertical force $$P$$ is applied at point $$C.$$ GATE CE 2005 Structural Analysis - Energy Principle Question 12 English

Deflection of the point $$C$$ is

A
$$\left( {{{2\sqrt 2 + 1} \over 2}} \right){{PL} \over {EA}}$$
B
$$\sqrt 2 {{PL} \over {EA}}$$
C
$$\left( {2\sqrt 2 + 1} \right){{PL} \over {EA}}$$
D
$$\left( {\sqrt 2 + 1} \right){{PL} \over {EA}}$$
2
GATE CE 2005
MCQ (Single Correct Answer)
+2
-0.6
A truss is shown in the figure. Members are to equal cross section $$A$$ and same modulus of elasticity $$E.$$ $$A$$ vertical force $$P$$ is applied at point $$C.$$ GATE CE 2005 Structural Analysis - Energy Principle Question 13 English

Force in the member $$AB$$ of the truss is

A
$${P \over {\sqrt 2 }}$$
B
$${P \over {\sqrt 3 }}$$
C
$${P \over 2}$$
D
$$P$$
3
GATE CE 2003
MCQ (Single Correct Answer)
+2
-0.6
In a redundant joint model, three bar members are pin connected at $$Q$$ as shown in the figure. Under some load placed at $$Q$$, the elongation of the members $$MQ$$ and $$OQ$$ are found to be $$48$$ $$mm$$ and $$35$$ $$mm$$ respectively. Then the horizontal displacement $$'u'$$ and the vertical displacement $$'v'$$ of the node $$Q,$$ in $$mm,$$ will be respectively, GATE CE 2003 Structural Analysis - Energy Principle Question 7 English
A
$$-6.64$$ and $$56.14$$
B
$$6.64$$ and $$56.14$$
C
$$0.0$$ and $$59.41$$
D
$$59.41$$ and $$0.0$$
4
GATE CE 2000
MCQ (Single Correct Answer)
+2
-0.6
For the structure shown below, the vertical deflection at point $$A$$ is given by GATE CE 2000 Structural Analysis - Energy Principle Question 8 English
A
$${{P{L^3}} \over {81EI}}$$
B
$${{2P{L^3}} \over {81EI}}$$
C
Zero
D
$${{P{L^3}} \over {72EI}}$$
PREVIOUS NEXT
GATE CE Subjects
Engineering Mechanics
Work Energy Principle and Impulse Momentum Equation Equilibrium of Force Systems
Strength of Materials Or Solid Mechanics
Pure Bending Shear Stress In Beams Simple Stresses Complex Stress Centroid and Moment of Inertia Torsion Shear Force and Bending Moment Deflection of Beams Thin Cylinder Strain Energy Method Columns and Struts Propped Cantilever Beam
Structural Analysis
Stability and Static Indeterminacy Methods of Analysis Plastic Analysis Moment Distribution Method Indeterminacy Energy Principle Influence Line Diagram Arches and Cable Slope Deflection Method Truss Matrix Method
Construction Material and Management
Critical Path Method Construction Materials Program Evolution Review Technique
Reinforced Cement Concrete
Singly Reinforced Sections Workmenship and Fundamentals Doubly Reinforced Sections Flanged Beams Limit State of Collapse Shear Limit State of Collapse Torsion Limit State of Collapse Compression Footings Bond Limit State of Serviceability Prestressed Concrete Slabs
Steel Structures
Eccentric Connections Plate Girder Tension Members Welded Connections Materials and Specifications Riveted Joints and Bolted Joints Beams Compression Members
Geotechnical Engineering
Origin of Soils Definitions and Properties of Soils Classification of Soils and Clay Mineralogy Effective Stress and Permeability Seepage Analysis Compaction of Soil Compressibility and Consolidation Shear Strength of Soil Stress Distribution of Soil Retaining Wall and Earth Pressure Stability of Slopes Shallow Foundation Pile Foundation Soil Stabilization
Fluid Mechanics and Hydraulic Machines
Fluid Pressure and Measurement Hydrostatic Forces Fluid Dynamics Boundary Layer Theory Drag and Lift Dimensional Analysis Flow Through Pipes Open Channel Flow Hydraulic Machines Properties of Fluids Fluid Statics
Hydrology
Precipitation and Frequency of Rainfall Data Evaporation and Transpiration Infiltration Hydrograph Flood Estimation and Flood Routing Well Hydraulics and River Gauging
Irrigation
Gravity Dams and Spillways Water Requirement of Crops
Geomatics Engineering Or Surveying
Levelling Traversing Theodolites and Plane Table Surveying Measurement of Area, Volume and Theory of Errors and Survey Adjustment Curves Field Astronomy and Photogrammetric Surveying Basics of GIS, GPS and Remote Sensing Angular Measurements and Compass Survey Basic Concepts Linear Measurements and Chain Survey
Environmental Engineering
Sources and Coveyances Water Quality Control of Water Treatment of Water Water Demand Waste Water Characteristics Sewage System and Sewer Appurtenances Treatment of Sewage Disposal of Sewage Effluent Solid Waste Management Air Pollution Noise Pollution
Transportation Engineering
Highway Devolopment and Planning Highway Geometric Design Traffic Engineering Highway Materials Pavement Design Railway, Runway and Taxiway Design
Engineering Mathematics
Probability and Statistics Calculus Complex Variable Differential Equations Linear Algebra Numerical Methods Vector Calculus Transform Theory
General Aptitude
Numerical Ability Logical Reasoning Verbal Ability
EXAM MAP
Joint Entrance Examination
JEE MainJEE AdvancedMHT CETBITSATCOMEDKWB JEEKCETVITEEEAP EAPCETTS EAMCETIAT (IISER)
Medical
NEETAIIMS
Graduate Aptitude Test in Engineering
GATE CSEGATE ECEGATE EEGATE MEGATE CEGATE PIGATE IN
Civil Services
UPSC Civil Service
Defence
NDA
Staff Selection Commission
SSC CGL Tier I
CBSE
Class 12