ExamSIDE (Powered by ExamGOAL)
Questions
PREVIOUS NEXT
1
GATE CE 2015 Set 1
Numerical
+1
-0
Two triangular wedges are glued together as shown in the following figure. The stress acting normal to the interface, $${\sigma _n}$$ is _____$$MPa.$$ GATE CE 2015 Set 1 Strength of Materials Or Solid Mechanics - Complex Stress Question 16 English
Your input ____
2
GATE CE 2012
MCQ (Single Correct Answer)
+1
-0.3
If a small concrete cube is submerged deep in still water in such a way that the pressure exerted on all faces of the cube is $$p,$$ then the maximum shear stress developed inside the cube is
A
$$0$$
B
$${p \over 2}$$
C
$$p$$
D
$$2p$$
3
GATE CE 2010
MCQ (Single Correct Answer)
+1
-0.3
The major and minor principal stresses at a point are $$3MPa$$ and $$-3MPa$$ respectively. The maximum shear stress at the point is
A
Zero
B
$$3$$ $$MPa$$
C
$$6$$ $$MPa$$
D
$$9MPa$$
4
GATE CE 2009
MCQ (Single Correct Answer)
+1
-0.3
Consider the following statements:
$$1.$$ On a principal plane, only normal stress acts
$$2.$$ On a principal plane, both normal and shear stresses act
$$3.$$ On a principal plane, only shear stress acts
$$4.$$ Isotropic state of stress is independent of frame of reference.

Which of the above statements is/are correct ?

A
$$1$$ and $$4$$
B
$$2$$ only
C
$$2$$ and $$4$$
D
$$2$$ and $$3$$
PREVIOUS NEXT
GATE CE Subjects
Engineering Mechanics
Work Energy Principle and Impulse Momentum Equation Equilibrium of Force Systems
Strength of Materials Or Solid Mechanics
Centroid and Moment of Inertia Torsion Pure Bending Shear Stress In Beams Strain Energy Method Columns and Struts Complex Stress Deflection of Beams Thin Cylinder Simple Stresses Shear Force and Bending Moment Propped Cantilever Beam
Structural Analysis
Energy Principle Truss Stability and Static Indeterminacy Methods of Analysis Indeterminacy Arches and Cable Slope Deflection Method Matrix Method Moment Distribution Method Influence Line Diagram Plastic Analysis
Construction Material and Management
Critical Path Method Construction Materials Program Evolution Review Technique
Reinforced Cement Concrete
Doubly Reinforced Sections Limit State of Collapse Shear Footings Bond Slabs Limit State of Collapse Torsion Limit State of Serviceability Prestressed Concrete Singly Reinforced Sections Workmenship and Fundamentals Flanged Beams Limit State of Collapse Compression
Steel Structures
Eccentric Connections Plate Girder Tension Members Welded Connections Materials and Specifications Riveted Joints and Bolted Joints Beams Compression Members
Geotechnical Engineering
Origin of Soils Definitions and Properties of Soils Classification of Soils and Clay Mineralogy Effective Stress and Permeability Seepage Analysis Compaction of Soil Compressibility and Consolidation Shear Strength of Soil Stress Distribution of Soil Retaining Wall and Earth Pressure Stability of Slopes Shallow Foundation Pile Foundation Soil Stabilization
Fluid Mechanics and Hydraulic Machines
Fluid Pressure and Measurement Fluid Dynamics Boundary Layer Theory Drag and Lift Flow Through Pipes Open Channel Flow Hydraulic Machines Properties of Fluids Fluid Statics
Hydrology
Precipitation and Frequency of Rainfall Data Evaporation and Transpiration Infiltration Hydrograph Flood Estimation and Flood Routing
Irrigation
Water Requirement of Crops Gravity Dams and Spillways
Geomatics Engineering Or Surveying
Levelling Traversing Theodolites and Plane Table Surveying Measurement of Area, Volume and Theory of Errors and Survey Adjustment Field Astronomy and Photogrammetric Surveying Basics of GIS, GPS and Remote Sensing Angular Measurements and Compass Survey Basic Concepts Linear Measurements and Chain Survey
Environmental Engineering
Sources and Coveyances Water Quality Control of Water Treatment of Water Water Demand Waste Water Characteristics Treatment of Sewage Disposal of Sewage Effluent Solid Waste Management Air Pollution Noise Pollution
Transportation Engineering
Highway Devolopment and Planning Highway Geometric Design Traffic Engineering Highway Materials Pavement Design Railway, Runway and Taxiway Design
Engineering Mathematics
Probability and Statistics Differential Equations Transform Theory Calculus Complex Variable Linear Algebra Vector Calculus Numerical Methods
General Aptitude
Numerical Ability Logical Reasoning Verbal Ability
EXAM MAP
Joint Entrance Examination
JEE MainJEE AdvancedWB JEEBITSATMHT CETKCETCOMEDKVITEEEAP EAPCET
Medical
NEETAIIMS
Graduate Aptitude Test in Engineering
GATE CSEGATE ECEGATE EEGATE MEGATE CEGATE PIGATE IN
Civil Services
UPSC Civil Service
Defence
NDA
Staff Selection Commission
SSC CGL Tier I
CBSE
Class 12