GATE CE 2022 Set 1 | Torsion Question 4 | Strength of Materials Or Solid Mechanics

GATE CE 2022 Set 1

MCQ (Single Correct Answer)

-0.33

The hoop stress at a point on the surface of a thin cylindrical pressure vessel is computed to be 30.0 MPa. The value of maximum shear stress at this point is

7.5 MPa

15.0 MPa

30 MPa

22.5 MPa

GATE CE 2006

MCQ (Single Correct Answer)

-0.3

A long shaft of diameter $$d$$ is subjected to twisting moment $$T$$ at its ends. The maximum normal stress acting at its cross-section is equal to

zero

$${{16T} \over {\pi {d^3}}}$$

$${{32T} \over {\pi {d^3}}}$$

$${{64T} \over {\pi {d^3}}}$$

GATE CE Subjects

Browse all chapters by subject

Irrigation

Gravity Dams and Spillways Water Requirement of Crops

Engineering Mechanics

Equilibrium of Force Systems Work Energy Principle and Impulse Momentum Equation

General Aptitude

Numerical Ability Logical Reasoning Verbal Ability

Transportation Engineering

Highway Devolopment and Planning Highway Geometric Design Traffic Engineering Highway Materials Pavement Design Railway, Runway and Taxiway Design

Hydrology

Precipitation and Frequency of Rainfall Data Evaporation and Transpiration Infiltration Hydrograph Flood Estimation and Flood Routing Well Hydraulics and River Gauging

Environmental Engineering

Sources and Coveyances Water Quality Control of Water Treatment of Water Water Demand Waste Water Characteristics Sewage System and Sewer Appurtenances Treatment of Sewage Disposal of Sewage Effluent Solid Waste Management Air Pollution Noise Pollution

Steel Structures

Materials and Specifications Riveted Joints and Bolted Joints Compression Members Beams Plate Girder Welded Connections Tension Members Eccentric Connections

Engineering Mathematics

Vector Calculus Numerical Methods Differential Equations Linear Algebra Complex Variable Probability and Statistics Transform Theory Calculus

Structural Analysis

Matrix Method Methods of Analysis Energy Principle Arches and Cable Truss Stability and Static Indeterminacy Moment Distribution Method Indeterminacy Influence Line Diagram Plastic Analysis Slope Deflection Method

Geomatics Engineering Or Surveying

Measurement of Area, Volume and Theory of Errors and Survey Adjustment Curves Theodolites and Plane Table Surveying Levelling Traversing Basics of GIS, GPS and Remote Sensing Field Astronomy and Photogrammetric Surveying Linear Measurements and Chain Survey Angular Measurements and Compass Survey Basic Concepts

Reinforced Cement Concrete

Workmenship and Fundamentals Limit State of Serviceability Singly Reinforced Sections Footings Prestressed Concrete Bond Limit State of Collapse Shear Slabs Flanged Beams Limit State of Collapse Compression Limit State of Collapse Torsion Doubly Reinforced Sections

Fluid Mechanics and Hydraulic Machines

Drag and Lift Boundary Layer Theory Fluid Dynamics Flow Through Pipes Dimensional Analysis Open Channel Flow Fluid Pressure and Measurement Hydraulic Machines Hydrostatic Forces Properties of Fluids Fluid Statics

Construction Material and Management

Program Evolution Review Technique Critical Path Method Construction Materials

Strength of Materials Or Solid Mechanics

Simple Stresses Pure Bending Centroid and Moment of Inertia Shear Stress In Beams Complex Stress Strain Energy Method Thin Cylinder Deflection of Beams Columns and Struts Shear Force and Bending Moment Torsion Propped Cantilever Beam

Geotechnical Engineering

Origin of Soils Definitions and Properties of Soils Classification of Soils and Clay Mineralogy Effective Stress and Permeability Seepage Analysis Compaction of Soil Compressibility and Consolidation Shear Strength of Soil Stress Distribution of Soil Retaining Wall and Earth Pressure Stability of Slopes Shallow Foundation Pile Foundation Soil Stabilization