ExamSIDE (Powered by ExamGOAL)
Questions
NEXT
1
GATE CE 2024 Set 2
MCQ (Single Correct Answer)
+2
-0.833

A homogeneous, prismatic, linearly elastic steel bar fixed at both the ends has a slenderness ratio (l/r) of 105, where l is the bar length and r is the radius of gyration. The coefficient of thermal expansion of steel is $12 \times 10^{-6}$ $^{\circ}$C. Consider the effective length of the steel bar as $0.5l$ and neglect the self-weight of the bar.

The differential increase in temperature (rounded off to the nearest integer) at which the bar buckles is

A

298 $^{\circ}$C

B

85 $^{\circ}$C

C

400 $^{\circ}$C

D

250 $^{\circ}$C

2
GATE CE 2017 Set 1
Numerical
+2
-0
Consider two axially loaded columns, namely. $$1$$ and $$2,$$ made of a linear elastic material with Young's modulus $$2 \times {10^5}\,\,MPa,$$ square cross-section with side $$10$$ $$mm$$, and length $$1$$ $$m.$$ For Column $$1,$$ one end is fixed and the other end is free. For column $$2,$$ one end is fixed and the other end is pinned. Based on the Euler's theory, the ratio (up to one decimal place) of the buckling load of Column $$2$$ to the buckling load of column $$1$$ is ___________
Your input ____
3
GATE CE 2014 Set 1
MCQ (Single Correct Answer)
+2
-0.6
If the following equation establishes equilibrium in slightly bent position, the mid-span deflection of a member shown in the figure is
$${{{d^2}y} \over {d{x^2}}} + {P \over {EI}}y = 0$$ GATE CE 2014 Set 1 Strength of Materials Or Solid Mechanics - Columns and Struts Question 4 English

If $$'a'$$ is amplitude constant for $$y,$$ then

A
$$y = {1 \over P}\left( {1 - a\,\cos {{2\pi x} \over L}} \right)$$
B
$$y = {1 \over P}\left( {1 - a\,sin{{2\pi x} \over L}} \right)$$
C
$$y = a\,\sin {{n\pi x} \over L}$$
D
$$y = a\,\cos {{n\pi x} \over L}$$
4
GATE CE 2012
MCQ (Single Correct Answer)
+2
-0.6
The sketch shows a column with a pin at the base and rollers at the top. It is subjected to an axial force $$P$$ and a moment $$M$$ at mid-height. The reaction$$(s)$$ at $$R$$ is/are GATE CE 2012 Strength of Materials Or Solid Mechanics - Columns and Struts Question 5 English
A
a vertical force equal to $$P$$
B
a vertical force equal to $$P/2$$
C
a vertical force equal to $$P$$ and a horizontal force equal to $$M/h$$
D
a vertical force equal to $$P/2$$ and a horizontal force equal to $$M/h$$
NEXT
GATE CE Subjects
Engineering Mechanics
Equilibrium of Force Systems Work Energy Principle and Impulse Momentum Equation
Strength of Materials Or Solid Mechanics
Centroid and Moment of Inertia Torsion Pure Bending Shear Stress In Beams Strain Energy Method Columns and Struts Complex Stress Deflection of Beams Thin Cylinder Simple Stresses Shear Force and Bending Moment Propped Cantilever Beam
Structural Analysis
Energy Principle Truss Stability and Static Indeterminacy Methods of Analysis Indeterminacy Arches and Cable Slope Deflection Method Matrix Method Moment Distribution Method Influence Line Diagram Plastic Analysis
Construction Material and Management
Critical Path Method Construction Materials Program Evolution Review Technique
Reinforced Cement Concrete
Doubly Reinforced Sections Limit State of Collapse Shear Footings Bond Slabs Limit State of Collapse Torsion Limit State of Serviceability Prestressed Concrete Singly Reinforced Sections Workmenship and Fundamentals Flanged Beams Limit State of Collapse Compression
Steel Structures
Eccentric Connections Plate Girder Tension Members Welded Connections Materials and Specifications Riveted Joints and Bolted Joints Beams Compression Members
Geotechnical Engineering
Origin of Soils Definitions and Properties of Soils Classification of Soils and Clay Mineralogy Effective Stress and Permeability Seepage Analysis Compaction of Soil Compressibility and Consolidation Shear Strength of Soil Stress Distribution of Soil Retaining Wall and Earth Pressure Stability of Slopes Shallow Foundation Pile Foundation Soil Stabilization
Fluid Mechanics and Hydraulic Machines
Fluid Pressure and Measurement Fluid Dynamics Boundary Layer Theory Drag and Lift Flow Through Pipes Open Channel Flow Hydraulic Machines Properties of Fluids Fluid Statics
Hydrology
Precipitation and Frequency of Rainfall Data Evaporation and Transpiration Infiltration Hydrograph Flood Estimation and Flood Routing
Irrigation
Gravity Dams and Spillways Water Requirement of Crops
Geomatics Engineering Or Surveying
Levelling Traversing Theodolites and Plane Table Surveying Measurement of Area, Volume and Theory of Errors and Survey Adjustment Field Astronomy and Photogrammetric Surveying Basics of GIS, GPS and Remote Sensing Angular Measurements and Compass Survey Basic Concepts Linear Measurements and Chain Survey
Environmental Engineering
Sources and Coveyances Water Quality Control of Water Treatment of Water Water Demand Waste Water Characteristics Treatment of Sewage Disposal of Sewage Effluent Solid Waste Management Air Pollution Noise Pollution
Transportation Engineering
Highway Devolopment and Planning Highway Geometric Design Traffic Engineering Highway Materials Pavement Design Railway, Runway and Taxiway Design
Engineering Mathematics
Probability and Statistics Calculus Complex Variable Differential Equations Linear Algebra Numerical Methods Vector Calculus Transform Theory
General Aptitude
Numerical Ability Logical Reasoning Verbal Ability
EXAM MAP
Joint Entrance Examination
JEE MainJEE AdvancedWB JEEBITSATMHT CETKCETCOMEDKVITEEEAP EAPCET
Medical
NEETAIIMS
Graduate Aptitude Test in Engineering
GATE CSEGATE ECEGATE EEGATE MEGATE CEGATE PIGATE IN
Civil Services
UPSC Civil Service
Defence
NDA
Staff Selection Commission
SSC CGL Tier I
CBSE
Class 12