Bentonite is commonly used bonding material for dry sand cores

According to Chvorinove's rule, the solidification time of a casting is proportional to [Volume/Surface area]n where $$n

A cylinder of $$150mm$$ diameter & $$200mm$$ height is to be cast with out any riser. The cylinder is moulded entire

The value of the following determinant $$\left[ {\matrix{ 1 & 4 & 9 \cr 4 & 9 & {16} \cr 9

The matrix $$\left[ {\matrix{ 1 & { - 4} \cr 1 & { - 5} \cr } } \right]$$ is an inverse of the matri

For the following matrix $$\left[ {\matrix{ 1 & { - 1} \cr 2 & 3 \cr } } \right]$$ the number of pos

Given matrix $$L = \left[ {\matrix{ 2 & 1 \cr 3 & 2 \cr 4 & 5 \cr } } \right]\,\,$$ and $$M

Solve for $$y$$ if $${{{d^2}y} \over {d{t^2}}} + 2{{dy} \over {dt}} + y = 0$$ with $$y(0)=1$$ and $${y^1}\left( 0 \right

If for a matrix, rank equals both the number of rows and number of columns, then the matrix is called

The composition of an oxy-acetylene flame for cutting of steel contain more oxygen.

Parting-off operation is carried out on a cylindrical work-piece of $$100mm$$ diameter. The groove width is $$2$$ $$mm$$

A part can be machined in $$30$$ minutes on an engine lathe where as it can be machined in $$6$$ minutes on a turret lat

In an orthogonal cutting operation, the cutting velocity is $$30$$ $$m/min$$ and the chip velocity $$15$$ $$m/min.$$ If

In an orthogonal cutting operation, the cutting velocity is $$30$$ $$m/min$$ and the chip velocity $$15$$ $$m/min.$$ If

In an orthogonal cutting operation, The depth of cut $$=2$$ $$mm,$$ Width of cut $$=15$$ $$mm,$$ Cutting speed $$=0.5$

In an orthogonal cutting operation, The depth of cut $$=2$$ $$mm,$$ Width of cut $$=15$$ $$mm,$$ Cutting speed $$=0.5$

In an orthogonal cutting operation, The depth of cut $$=2$$ $$mm,$$ Width of cut $$=15$$ $$mm,$$ Cutting speed $$=0.5$

Parting-off operation is carried out on a cylindrical work-piece of $$100mm$$ diameter. The groove width is $$2$$ $$mm$$

$$FMS$$ is well suited to mass scale manufacturing.

In $$DNC$$ each machine tool is controlled by a dedicated computer.

$$FAPT$$ is a part programming language.

Match the following

Machinability of steels is improved by the addition of

In metal cutting $$BUE$$ formation results in

Only negative rake angles are used with the following tool material

The heat generated in metal cutting is dissipated in different proportions into environment, tool, chip and work-piece.

The function of draw bead in the deep drawing operation is to

In a bending operation, If the modulus of elasticity $$E$$ is increased keeping all other parameters unchanged, the spri

In blanking operation, the best way to improve the smoothness and squarness of the edges is to

In producing a punched hole of $$20mm$$ diameter, the dimension of the punch is ........ given the radial die clearance

In metal forming operation, the true strain in the $$X$$-direction is $$0.3$$ and in the $$Y$$-direction is $$-0.1.$$ Th

Forces in hot extrusion is a function of the strain hardening component of the billet material.

In order to reduce roll pressure in strip rolling, back tension can be applied to strip.

Which one of the following manufacturing process requires the provision of 'gutters'

A moving mandrel is used in

An annealed copper wire of $$25 mm$$ diameter is drawn into a wire of $$5$$ $$mm$$ dia. The average yield stress in this

Abbe's principle of alignment is used in measurements made in .................

The combination of slip gauges to obtain a dimension of $$10.35$$ $$mm$$ will be

A hole is specified as $$\phi 30 \pm 0.04mm$$ with $$\phi \,\,0.01\,\,M.$$ The virtual diameter of the hole (i.e the max